hardware:perenio:peacg01
This is an old revision of the document!
Table of Contents
Perenio PEACG01
Основано на базе референсного дизайна: CUS531MP3-NAND
Состоит из:
- CPU: QCA4531-BL3A
- RAM: winbond W9751G6KB-25 (DDR-2, 64MB)
- SPI Flash: mx25l3205d (512KB)
- NAND Flash: Macronix MX35LF1G4EAB (SLC, 128MB)
- USB Hub: GL850G
- USB-Serial: PL2303SA
- Clock: PCF8563 + Battery
- ZigBee: EFR32 MG1P232GG
Photos
Additional collected info
Boot log
U-Boot 1.1.4.svn5120 (Jan 12 2018 - 13:20:07)
cus531mp3 - Honey Bee 2.0DRAM:
sri
Honey Bee 2.0
ath_ddr_initial_config(195): (16bit) ddr2 init
ath_sys_frequency: cpu 650 ddr 597 ahb 216
tap = 0x00000003
Tap (low, high) = (0x8, 0x21)
Tap values = (0x14, 0x14, 0x14, 0x14)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 222k for U-Boot at: 83fc8000
Reserving 192k for malloc() at: 83f98000
Reserving 44 Bytes for Board Info at: 83f97fd4
Reserving 36 Bytes for Global Data at: 83f97fb0
Reserving 128k for boot params() at: 83f77fb0
Stack Pointer at: 83f77f98
Now running in RAM - U-Boot at: 83fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x16
flash size 0MB, sector count = 8
Flash: 512 kB
Power up PLL with outdiv = 0 then switch to 3
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Honey Bee ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
====== NAND Parameters ======
sc = 0x83ff8b20 page = 0x800 block = 0x20000
Setting 0x181162c0 to 0x2851a100
Hit any key to stop autoboot: 0
Loading from device 0: ath-spi-nand (offset 0x2200000)
Image Name: MIPS OpenWrt Linux-3.18.29
Created: 2018-05-02 9:39:12 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1476171 Bytes = 1.4 MB
Load Address: 80060000
Entry Point: 80060000
## Booting image at 81000000 ...
Image Name: MIPS OpenWrt Linux-3.18.29
Created: 2018-05-02 9:39:12 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1476171 Bytes = 1.4 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x81000040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
[ 0.000000] Linux version 3.18.29 (yangcanghua@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r6273) ) #50 Wed May 2 17:38:35 CST 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: ubi.mtd=8 ubootsvn=5120 board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init bootslot=1 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0),32m(root-0),2m(kernel-1)ro,32m(root-1),60m(overlay),34m@0x2200000(firmware1) production=0000 hwversion=V2.0 app_switch=default mem=64M rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 59916K/65536K available (3395K kernel code, 156K rwdata, 672K rodata, 184K init, 194K bss, 5620K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:650.000MHz, DDR:597.241MHz, AHB:216.666MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Performance counters: mips/24K PMU enabled, 2 32-bit counters available to each CPU, irq 13
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Qualcomm Atheros CUS531 MP3 nand reference board
[ 0.090000] ar724x-pci ar724x-pci.0: PCIe link is down
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.110000] ar71xx: invalid MDIO id 1
[ 0.550000] i2c-gpio i2c-gpio.0: using pins 17 (SDA) and 16 (SCL)
[ 0.560000] PCI host bridge to bus 0000:00
[ 0.560000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.570000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.570000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.580000] Bluetooth: Core ver 2.19
[ 0.580000] NET: Registered protocol family 31
[ 0.580000] Bluetooth: HCI device and connection manager initialized
[ 0.590000] Bluetooth: HCI socket layer initialized
[ 0.590000] Bluetooth: L2CAP socket layer initialized
[ 0.600000] Bluetooth: SCO socket layer initialized
[ 0.600000] Switched to clocksource MIPS
[ 0.610000] NET: Registered protocol family 2
[ 0.610000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.610000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.620000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.630000] TCP: reno registered
[ 0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.640000] NET: Registered protocol family 1
[ 0.650000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.680000] msgmni has been set to 117
[ 0.690000] io scheduler noop registered
[ 0.690000] io scheduler deadline registered (default)
[ 0.700000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.700000] console [ttyS0] disabled
[ 0.730000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.740000] console [ttyS0] enabled
[ 0.740000] console [ttyS0] enabled
[ 0.740000] bootconsole [early0] disabled
[ 0.740000] bootconsole [early0] disabled
[ 0.750000] m25p80 spi0.0: found mx25l3205d, expected m25p80
[ 0.760000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[ 0.760000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.770000] Creating 5 MTD partitions on "spi0.0":
[ 0.780000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.780000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.790000] 0x000000050000-0x000000060000 : "u-boot-env-bak"
[ 0.790000] 0x000000060000-0x000000070000 : "reserved"
[ 0.800000] 0x000000070000-0x000000080000 : "art"
[ 0.810000] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0x12
[ 0.810000] nand: Macronix MX35LF1G4EAB 1G 3.3V 8-bit
[ 0.820000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 0.830000] nand: WARNING: spi0.1: the ECC used on your system is too weak compared to the one required by the NAND chip
[ 0.840000] Scanning device for bad blocks
[ 0.890000] Bad eraseblock 735 at 0x000005be0000
[ 0.910000] 6 cmdlinepart partitions found on MTD device spi0.1
[ 0.910000] Creating 6 MTD partitions on "spi0.1":
[ 0.920000] 0x000000000000-0x000000200000 : "kernel-0"
[ 0.930000] 0x000000200000-0x000002200000 : "root-0"
[ 0.930000] 0x000002200000-0x000002400000 : "kernel-1"
[ 0.940000] 0x000002400000-0x000004400000 : "root-1"
[ 0.940000] 0x000004400000-0x000008000000 : "overlay"
[ 0.950000] 0x000002200000-0x000004400000 : "firmware1"
[ 0.990000] libphy: ag71xx_mdio: probed
[ 1.580000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 1.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.180000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.220000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.230000] rtc-pcf8563 0-0051: chip found, driver version 0.4.3
[ 2.240000] rtc (null): invalid alarm value: 2021-4-13 34:22:0
[ 2.240000] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
[ 2.250000] Bluetooth: HCI UART driver ver 2.2
[ 2.260000] Bluetooth: HCI H4 protocol initialized
[ 2.260000] Bluetooth: HCI BCSP protocol initialized
[ 2.270000] Bluetooth: HCIATH3K protocol initialized
[ 2.270000] TCP: cubic registered
[ 2.280000] NET: Registered protocol family 10
[ 2.280000] NET: Registered protocol family 17
[ 2.290000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.300000] 8021q: 802.1Q VLAN Support v1.8
[ 2.310000] UBI: attaching mtd8 to ubi0
[ 2.800000] UBI: scanning is finished
[ 2.830000] UBI: attached mtd8 (name "root-1", size 32 MiB) to ubi0
[ 2.840000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.840000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.850000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.860000] UBI: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
[ 2.860000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.870000] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 29864118
[ 2.880000] UBI: available PEBs: 0, total reserved PEBs: 256, PEBs reserved for bad PEB handling: 20
[ 2.890000] UBI: background thread "ubi_bgt0d" started, PID 332
[ 2.900000] mtd: device 11 (rootfs) set to be root filesystem
[ 2.900000] UBI: attaching mtd9 to ubi1
[ 3.820000] UBI: scanning is finished
[ 3.850000] UBI: attached mtd9 (name "overlay", size 60 MiB) to ubi1
[ 3.860000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.860000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.870000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.880000] UBI: good PEBs: 479, bad PEBs: 1, corrupted PEBs: 0
[ 3.890000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[ 3.890000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3988775088
[ 3.900000] UBI: available PEBs: 456, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
[ 3.910000] rtc-pcf8563 0-0051: setting system clock to 2021-03-31 17:47:17 UTC (1617212837)
[ 3.920000] UBI: background thread "ubi_bgt1d" started, PID 350
[ 3.940000] VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
[ 3.940000] Freeing unused kernel memory: 184K (80482000 - 804b0000)
[ 4.810000] init: Console is alive
[ 4.810000] init: - watchdog -
[ 6.410000] usbcore: registered new interface driver usbfs
[ 6.410000] usbcore: registered new interface driver hub
[ 6.420000] usbcore: registered new device driver usb
[ 6.430000] Button Hotplug driver version 0.4.1
[ 6.440000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.450000] ehci-platform: EHCI generic platform driver
[ 6.450000] ehci-platform ehci-platform: EHCI Host Controller
[ 6.460000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 6.470000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.500000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.500000] hub 1-0:1.0: USB hub found
[ 6.510000] hub 1-0:1.0: 1 port detected
[ 6.510000] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.830000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.860000] init: - preinit -
[ 7.260000] hub 1-1:1.0: USB hub found
[ 7.270000] hub 1-1:1.0: 4 ports detected
[ 7.720000] usb 1-1.2: new full-speed USB device number 3 using ehci-platform
[ 7.730000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.770000] random: mktemp urandom read with 13 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.910000] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[ 8.000000] usb 1-1.4: device descriptor read/64, error -32
[ 8.190000] usb 1-1.4: device descriptor read/64, error -32
[ 8.380000] usb 1-1.4: new full-speed USB device number 5 using ehci-platform
[ 8.470000] usb 1-1.4: device descriptor read/64, error -32
[ 8.660000] usb 1-1.4: device descriptor read/64, error -32
[ 8.850000] usb 1-1.4: new full-speed USB device number 6 using ehci-platform
[ 9.280000] usb 1-1.4: device not accepting address 6, error -32
[ 9.360000] usb 1-1.4: new full-speed USB device number 7 using ehci-platform
[ 9.790000] usb 1-1.4: device not accepting address 7, error -32
[ 9.790000] usb 1-1-port4: unable to enumerate USB device
Before mount_root
[ 10.950000] mount_root: loading kmods from internal overlay
[ 11.380000] block: attempting to load /etc/config/fstab
[ 11.380000] block: unable to load configuration (fstab: Entry not found)
[ 11.390000] block: no usable configuration
[ 11.400000] jffs2: write-buffering enabled buffer (2048) erasesize (126976)
[ 11.530000] jffs2: notice: (416) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 11.910000] block: attempting to load /etc/config/fstab
[ 11.910000] block: unable to load configuration (fstab: Entry not found)
[ 11.920000] block: no usable configuration
[ 11.930000] mount_root: switching to jffs2 overlay
After mount_root
[ 11.990000] procd: - early -
[ 11.990000] procd: - watchdog -
[ 12.760000] procd: - ubus -
[ 13.780000] procd: - init -
Please press Enter to activate this console.
[ 14.370000] jffs2: notice: (420) check_node_data: wrong data CRC in data node at 0x006ade94: read 0x3bd045b9, calculated 0x446b1e34.
[ 15.240000] NET: Registered protocol family 8
[ 15.240000] NET: Registered protocol family 20
[ 15.280000] l2tp_core: L2TP core driver, V2.0
[ 15.290000] l2tp_netlink: L2TP netlink interface
[ 15.290000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 15.300000] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 15.310000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 15.320000] gre: GRE over IPv4 demultiplexor driver
[ 15.330000] ip_gre: GRE over IPv4 tunneling driver
[ 15.350000] PPP generic driver version 2.4.2
[ 15.380000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.410000] i2c /dev entries driver
[ 15.430000] hidraw: raw HID events driver (C) Jiri Kosina
[ 15.450000] u32 classifier
[ 15.450000] input device check on
[ 15.450000] Actions configured
[ 15.460000] Mirror/redirect action on
[ 15.470000] nf_conntrack version 0.5.0 (939 buckets, 3756 max)
[ 15.490000] Loading modules backported from Linux version v3.18-116968-ga5cea28c4c2f
[ 15.500000] Backport generated by backports.git backports-20160216-0-ge3c56e41
[ 15.700000] ###################################################
[ 15.700000] BTCOEX:Disabled
[ 15.700000] priority_time:2
[ 15.700000] first_slot_time:18
[ 15.700000] wl_active_time:0
[ 15.700000] wl_qc_time:0
[ 15.700000] time_extend:10
[ 15.700000] ack_cts:0
[ 15.700000] btcoex_period:45
[ 15.700000] btcoex_duty_cycle:40
[ 15.730000] ###################################################
[ 15.750000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[ 15.780000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.820000] nf_conntrack_rtsp v0.6.21 loading
[ 15.860000] nf_nat_rtsp v0.6.21 loading
[ 15.880000] PPP MPPE Compression module registered
[ 15.890000] NET: Registered protocol family 24
[ 15.900000] PPTP driver version 0.8.5
[ 15.920000] usbcore: registered new interface driver usbserial
[ 15.930000] usbcore: registered new interface driver usbserial_generic
[ 15.930000] usbserial: USB Serial support registered for generic
[ 16.000000] xt_time: kernel timezone is -0000
[ 16.010000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 16.040000] usbcore: registered new interface driver pl2303
[ 16.050000] usbserial: USB Serial support registered for pl2303
[ 16.060000] pl2303 1-1.2:1.0: pl2303 converter detected
[ 16.060000] usb 1-1.2: pl2303 converter now attached to ttyUSB0
[ 33.540000] device eth1 entered promiscuous mode
[ 33.560000] br-lan: port 1(eth1) entered forwarding state
[ 33.570000] br-lan: port 1(eth1) entered forwarding state
[ 33.630000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 34.480000] br-lan: port 1(eth1) entered disabled state
[ 36.760000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 39.090000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 47.640000] random: nonblocking pool is initialized
[ 48.960000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 50.380000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 427.450000] eth0: link up (100Mbps/Full duplex)
[ 427.450000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
BusyBox v1.23.2 (2021-09-13 20:40:24 UTC) built-in shell (ash)
,9&G3
HHHHHXSXAHHHH5
HHH: GHH;
HH5 HHHHHHH& HHH
XHr HHHA ,HHHH HH
HH &HH
. . . HG
HH HHHHHHHG AHHHHHHH HH HHHH 3HHHHHHH HHhHHHHHHH HH HrsHH HG
HHH& HHH HHA 5HHS HHHH3 HH& HHH HHHr rHH HH HHA sHH sHH2
HH; SHH HH HH HHA HH& HH. HHS HHS HH HH ;HH HH
HH HH HHHHHHHHHHHH HH HHHHHHHHHHHHX HH, HH2 HH HH ,H3
HH HH HH HH HHX HH, HH2 HH HH &H:
HHH HHi 9HH G HH HH i: HH, HH2 HH HH HH
HHAHHHHHHHH HHHHHHHHH HH HHHHHHHHH9 HH, HH2 HH GHHHHHHHH
HH hHG; 5HHA; sr ;AHH5 ,i .i ii iX5;
HH
HH
---------------------------------------------------------------
Preview version 1.0.3X Perenio 2018 © ... (Gateway PEACG01 )
---------------------------------------------------------------
u-boot env
ath> printenv
bootargs=board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=5,2048 root=/dev/mtdblock8 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),128k(reserved),64k(art);spi0.1:2m(kernel),36m(rootfs),90m(data),38m@0x0(firmware) rootfstype=squashfs,jffs2 noinitrd
bootcmd=if test ${bootslot} -ne 1;then run boot_from_slot_0;else run boot_from_slot_1;fi
bootdelay=2
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.1.2
serverip=192.168.1.10
app_switch=default
kernel_0_start=0x0
root_0_start=0x400000
mtdparts0=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0)ro,32m(root-0),2m(kernel-1),32m(root-1),60m(overlay),34m@0x0(firmware0)
boot_from_slot_0=setenv bootargs ubi.mtd=6 ubootsvn=${ubootsvn} ${std_bootargs0} mtdparts=${mtdparts0} production=${production} hwversion=${hwversion} app_switch=${app_switch}; nboot 0x81000000 0 ${kernel_0_start}
kernel_1_start=0x2200000
root_1_start=0x2600000
mtdparts1=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0),32m(root-0),2m(kernel-1)ro,32m(root-1),60m(overlay),34m@0x2200000(firmware1)
boot_from_slot_1=setenv bootargs ubi.mtd=8 ubootsvn=${ubootsvn} ${std_bootargs1} mtdparts=${mtdparts1} production=${production} hwversion=${hwversion} app_switch=${app_switch}; nboot 0x81000000 0 ${kernel_1_start}
std_bootargs0=board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init bootslot=0
std_bootargs1=board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init bootslot=1
production=0000
sysreset=0
bootKernelFailCount=0
flash_uboot=tftp 0x80060000 u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
flash_kernel-0=tftp 0x80060000 kernel.bin&&nand erase 0x0 0x200000&&nand write $fileaddr 0x0 $filesize
flash_root-0=tftp 0x80060000 root.bin&&nand erase 0x200000 0x2000000&&nand write $fileaddr 0x200000 $filesize
flash_kernel-1=tftp 0x80060000 kernel.bin&&nand erase 0x2200000 0x200000&&nand write $fileaddr 0x2200000 $filesize
flash_root-1=tftp 0x80060000 root.bin&&nand erase 0x2400000 0x2000000&&nand write $fileaddr 0x2400000 $filesize
overy_start=0x4400000
erase_overlay=nand erase 0x4400000 0x3C00000
flash_firmware=run flash_uboot;run flash_kernel-0;run flash_root-0;run flash_kernel-1;run flash_root-1;run erase_overlay
store_factory_env=erase 0x9f050000 +0x10000;cp.b 0x9f040000 0x80060000 0x10000;cp.b 0x80060000 0x9f050000 0x10000
restore_factory_env=erase 0x9f040000 +0x10000;cp.b 0x9f050000 0x80060000 0x10000;cp.b 0x80060000 0x9f040000 0x10000
ethact=eth0
DevType=1
customer=Perenio
hwversion=V2.0
UUID=0a098d9e-8cff-48de-8dbf-e0b9aa905bd2
PIN=61589273
SN=3D67177F9D8C1A1
model_id=PEACG01_Ihvg
model_key=IMK5wrXC
uboot_env_init=1
mode=ldsGateReleaseMode
model=PEACG01
bootslot=1
fw_new_version=0.1.44
fw_version=0.1.44
ncp_version=6.6.3
camera_provisioned=false
wireless_enabled=true
wireless_mode=ap
ethernet_enabled=true
stdin=serial
stdout=serial
stderr=serial
ubootsvn=5120
Environment size: 3130/65532 bytes
netstat
root@OpenWrt:/# netstat Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost:44987 localhost:1883 ESTABLISHED tcp 0 0 localhost:1883 localhost:44986 ESTABLISHED tcp 0 0 localhost:44986 localhost:1883 ESTABLISHED tcp 0 0 localhost:1883 localhost:44987 ESTABLISHED udp 0 0 172.16.0.143:ntp 107-194-210-155.lightspeed.lsvlky.sbcglobal.net:ntp ESTABLISHED Active UNIX domain sockets (w/o servers) Proto RefCnt Flags Type State I-Node Path unix 9 [ ] DGRAM 1939 /dev/log unix 2 [ ] DGRAM 4821 /var/run/hostapd/wlan0 unix 2 [ ] DGRAM 7580 unix 2 [ ] DGRAM 5759 unix 3 [ ] STREAM CONNECTED 1934 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 1933 unix 3 [ ] STREAM CONNECTED 5595 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 1944 unix 3 [ ] STREAM CONNECTED 5594 unix 3 [ ] STREAM CONNECTED 1978 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 1977 unix 3 [ ] STREAM CONNECTED 2177 unix 3 [ ] STREAM CONNECTED 516 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 515 unix 3 [ ] STREAM CONNECTED 2178 /var/run/ubus.sock unix 2 [ ] DGRAM 2936 unix 3 [ ] STREAM CONNECTED 1945 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 3760 /var/run/ubus.sock unix 2 [ ] DGRAM 4378 unix 3 [ ] STREAM CONNECTED 3759 unix 2 [ ] DGRAM 4971 unix 2 [ ] DGRAM 2262 unix 2 [ ] DGRAM 2328 unix 3 [ ] STREAM CONNECTED 4823 unix 2 [ ] DGRAM 2919 unix 3 [ ] STREAM CONNECTED 4824 /var/run/ubus.sock root@OpenWrt:/# netstat -n -a Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:1883 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:44987 127.0.0.1:1883 ESTABLISHED tcp 0 0 127.0.0.1:1883 127.0.0.1:44986 ESTABLISHED tcp 0 0 127.0.0.1:44986 127.0.0.1:1883 ESTABLISHED tcp 0 0 127.0.0.1:1883 127.0.0.1:44987 ESTABLISHED tcp 0 0 :::5000 :::* LISTEN tcp 0 0 :::80 :::* LISTEN tcp 0 0 :::53 :::* LISTEN tcp 0 0 :::22 :::* LISTEN tcp 0 0 :::23 :::* LISTEN tcp 0 0 :::1883 :::* LISTEN udp 0 0 0.0.0.0:53 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:1900 0.0.0.0:* udp 0 0 172.16.0.143:123 107.194.210.155:123 ESTABLISHED udp 0 0 192.168.1.2:37521 0.0.0.0:* udp 0 0 192.168.1.2:5351 0.0.0.0:* udp 0 0 :::546 :::* udp 0 0 :::53 :::* udp 0 0 :::5351 :::* raw 0 0 :::58 :::* 58 Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 513 /var/run/ubus.sock unix 2 [ ACC ] STREAM LISTENING 5756 /var/run/bird.ctl unix 9 [ ] DGRAM 1939 /dev/log unix 2 [ ] DGRAM 4821 /var/run/hostapd/wlan0 unix 2 [ ] DGRAM 7580 unix 2 [ ] DGRAM 5759 unix 3 [ ] STREAM CONNECTED 1934 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 1933 unix 3 [ ] STREAM CONNECTED 5595 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 1944 unix 3 [ ] STREAM CONNECTED 5594 unix 3 [ ] STREAM CONNECTED 1978 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 1977 unix 3 [ ] STREAM CONNECTED 2177 unix 3 [ ] STREAM CONNECTED 516 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 515 unix 3 [ ] STREAM CONNECTED 2178 /var/run/ubus.sock unix 2 [ ] DGRAM 2936 unix 3 [ ] STREAM CONNECTED 1945 /var/run/ubus.sock unix 3 [ ] STREAM CONNECTED 3760 /var/run/ubus.sock unix 2 [ ] DGRAM 4378 unix 3 [ ] STREAM CONNECTED 3759 unix 2 [ ] DGRAM 4971 unix 2 [ ] DGRAM 2262 unix 2 [ ] DGRAM 2328 unix 3 [ ] STREAM CONNECTED 4823 unix 2 [ ] DGRAM 2919 unix 3 [ ] STREAM CONNECTED 4824 /var/run/ubus.sock
opkg list-installed
root@OpenWrt:/# opkg list-installed alsa-lib - 1.0.28-1 ath10k-firmware - g18118da-1 base-files - 157.2-unknown bird4 - 1.4.5-2 bird4-uci - 0.2 block-mount - 2016-01-10-96415afecef35766332067f4205ef3b2c7561d21 busybox - 1.23.2-1 curl - 7.40.0-3.2 dnsmasq-dhcpv6 - 2.73-1 dropbear - 2015.67-1 ethtool - 3.18-1 firewall - 2015-07-27 fstools - 2016-01-10-96415afecef35766332067f4205ef3b2c7561d21 gdb - 7.8-2 gdbserver - 7.8-2 glib2 - 2.44.1-1 hostapd - 2015-09-27-1 hostapd-common - 2015-09-27-1 hostapd-utils - 2015-09-27-1 i2c-tools - 3.1.2-1 ip - 4.0.0-1 ip6tables - 1.4.21-1 iperf - 2.0.5-1 iptables - 1.4.21-1 iptables-mod-conntrack-extra - 1.4.21-1 iptables-mod-ipopt - 1.4.21-1 iw - 4.3-1 iwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371 jshn - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9 kaa-camera-service - v2.2.18 kernel - 3.18.29-1-8ea585a6b5a768c445ceb8254de2ca34 kmod-art2 - 3.18.29+CS10.2v4.9.432-1 kmod-ath - 3.18.29+20160607-1 kmod-ath9k - 3.18.29+20160607-1 kmod-ath9k-common - 3.18.29+20160607-1 kmod-atm - 3.18.29-1 kmod-button-hotplug - 3.18.29-3 kmod-cfg80211 - 3.18.29+20160607-1 kmod-crypto-aead - 3.18.29-1 kmod-crypto-aes - 3.18.29-1 kmod-crypto-arc4 - 3.18.29-1 kmod-crypto-core - 3.18.29-1 kmod-crypto-ecb - 3.18.29-1 kmod-crypto-hash - 3.18.29-1 kmod-crypto-manager - 3.18.29-1 kmod-crypto-pcompress - 3.18.29-1 kmod-crypto-sha1 - 3.18.29-1 kmod-gpio-button-hotplug - 3.18.29-1 kmod-gpio-dev - 3.18.29-1 kmod-gre - 3.18.29-1 kmod-hid - 3.18.29-1 kmod-i2c-algo-bit - 3.18.29-1 kmod-i2c-core - 3.18.29-1 kmod-i2c-gpio - 3.18.29-1 kmod-i2c-gpio-custom - 3.18.29-2 kmod-ifb - 3.18.29-1 kmod-input-core - 3.18.29-1 kmod-input-evdev - 3.18.29-1 kmod-ip6tables - 3.18.29-1 kmod-ipt-conntrack - 3.18.29-1 kmod-ipt-conntrack-extra - 3.18.29-1 kmod-ipt-core - 3.18.29-1 kmod-ipt-ipopt - 3.18.29-1 kmod-ipt-nat - 3.18.29-1 kmod-ipt-nathelper-rtsp - 3.18.29+2.10-1 kmod-iptunnel - 3.18.29-1 kmod-l2tp - 3.18.29-1 kmod-l2tp-eth - 3.18.29-1 kmod-l2tp-ip - 3.18.29-1 kmod-lib-crc-ccitt - 3.18.29-1 kmod-lib-crc16 - 3.18.29-1 kmod-lib-textsearch - 3.18.29-1 kmod-mac80211 - 3.18.29+20160607-1 kmod-mppe - 3.18.29-1 kmod-nf-conntrack - 3.18.29-1 kmod-nf-conntrack6 - 3.18.29-1 kmod-nf-ipt - 3.18.29-1 kmod-nf-ipt6 - 3.18.29-1 kmod-nf-nat - 3.18.29-1 kmod-nf-nathelper - 3.18.29-1 kmod-nf-nathelper-extra - 3.18.29-1 kmod-nls-base - 3.18.29-1 kmod-nls-koi8r - 3.18.29-1 kmod-nls-utf8 - 3.18.29-1 kmod-ppp - 3.18.29-1 kmod-pppoa - 3.18.29-1 kmod-pppoe - 3.18.29-1 kmod-pppol2tp - 3.18.29-1 kmod-pppox - 3.18.29-1 kmod-pptp - 3.18.29-1 kmod-sched-connmark - 3.18.29-1 kmod-sched-core - 3.18.29-1 kmod-slhc - 3.18.29-1 kmod-sound-core - 3.18.29-1 kmod-udptunnel4 - 3.18.29-1 kmod-udptunnel6 - 3.18.29-1 kmod-usb-core - 3.18.29-1 kmod-usb-serial - 3.18.29-1 kmod-usb-serial-pl2303 - 3.18.29-1 kmod-usb-uhci - 3.18.29-1 kmod-usb2 - 3.18.29-1 libattr - 20150220-1 libblobmsg-json - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb libbz2 - 1.0.6-2 libc - 1.0.14-1 libcap - 2.24-1 libcares - 1.10.0-1 libcurl - 7.40.0-3.2 libdb47 - 4.7.25.4.NC-4.1 libdbus - 1.9.14-1 libexpat - 2.1.0-3 libffi - 3.0.13-1 libgcc - 4.8-linaro-1 libgdbm - 1.11-1 libgmp - 6.0.0-1 libical - 1.0-1 libip4tc - 1.4.21-1 libip6tc - 1.4.21-1 libiwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371 libiwinfo-lua - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371 libjson-c - 0.12-1 libjson-script - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb liblua - 5.1.5-1 liblxc - 1.1.3-1 liblzma - 5.2.1-2 liblzo - 2.08-1 libmagic - 5.25-1 libmosquitto - 1.4.8-1 libmysqlclient - 5.1.73-1 libncurses - 5.9-2 libnl - 3.2.21-1 libnl-tiny - 0.1-4 libopenssl - 1.0.2h-1 libpam - 1.1.8-4 libpcap - 1.5.3-1 libpolarssl - 1.3.15-1 libpthread - 1.0.14-1 libreadline - 6.3-1 librpc - 2015-11-04-a921e3ded051746f9f7cd5e5a312fb6771716aac librt - 1.0.14-1 libsqlite3 - 3081101-1 libstdcpp - 4.8-linaro-1 libthread-db - 1.0.14-1 libubox - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb libubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e libubus-lua - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e libuci - 2015-08-27.1-1 libuci-lua - 2015-08-27.1-1 libusb-1.0 - 1.0.19-1 libuuid - 2.25.2-4 libwebsockets-openssl - 1.3-chrome37-firefox30-1 libxml2 - 2.9.2-3 libxtables - 1.4.21-1 libyaml - 0.1.6-1 linux-atm - 2.5.2-5 logd - 2015-11-22-c086167a0154745c677f8730a336ea9cf7d71031 lua - 5.1.5-1 lxc - 1.1.3-1 lxc-common - 1.1.3-1 lxc-configs - 1.1.3-1 lxc-create - 1.1.3-1 lxc-hooks - 1.1.3-1 lxc-templates - 1.1.3-1 miniupnpd - 1.9.20150609-1 mosquitto - 1.4.8-1 mosquitto-client - 1.4.8-1 mtd - 24 nano - 2.5.3-1 netifd - 2015-12-16-245527193e90906451be35c2b8e972b8712ea6ab ntpclient - 2010_365-1 odhcp6c - 2015-07-29-dc186d6d2b0dd4ad23ca5fc69c00e81f796ff6d9 odhcpd - 2015-11-19-01d3f9d64486ac1daa144848944e877e7f0cb762 openssh-keygen - 7.1p2-1 openssh-server-pam - 7.1p2-1 openssh-sftp-server - 7.1p2-1 openssl-util - 1.0.2h-1 opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-9 opkg-smime - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-9 ppp - 2.4.7-6 ppp-mod-pppoa - 2.4.7-6 ppp-mod-pppoe - 2.4.7-6 ppp-mod-pppol2tp - 2.4.7-6 ppp-mod-pptp - 2.4.7-6 ppp-mod-radius - 2.4.7-6 ppp-multilink - 2.4.7-6 pppdump - 2.4.7-6 pppstats - 2.4.7-6 procd - 2015-10-29.1-d5fddd91b966424bb63e943e789704d52382cc18 python - 2.7.13-1 python-base - 2.7.13-1 python-codecs - 2.7.13-1 python-compiler - 2.7.13-1 python-ctypes - 2.7.13-1 python-db - 2.7.13-1 python-decimal - 2.7.13-1 python-distutils - 2.7.13-1 python-email - 2.7.13-1 python-gdbm - 2.7.13-1 python-light - 2.7.13-1 python-logging - 2.7.13-1 python-multiprocessing - 2.7.13-1 python-mysql - 1.2.5-1 python-ncurses - 2.7.13-1 python-openssl - 2.7.13-1 python-pip - 1.5.6-1 python-pydoc - 2.7.13-1 python-pyserial - 2.7-1 python-setuptools - 7.0-1 python-smbus - 3.1.2-1 python-sqlite3 - 2.7.13-1 python-unittest - 2.7.13-1 python-xml - 2.7.13-1 python-xmodem - 0.4.5-1 python-yaml - 3.11-1 python3-base - 3.4.3-2 python3-light - 3.4.3-2 qca-legacy-uboot-cus531mp3-nand - g18118da-1 qos-scripts - 1.2.1-7 resolveip - 2 rp-pppoe-relay - 3.11-1 rpcd - 2016-04-13-73aea9b8b621a1ce034bc6ee00c9d058a40c8a3d rpcd-mod-lxc - 20141012 simplejson - 3.6.5-1 sqlite3-cli - 3081101-1 sudo - 1.8.14p3-1 sysstat - 11.0.4-2 tc - 4.0.0-1 tcpdump - 4.5.1-4 terminfo - 5.9-2 uboot-envtools - 2014.10-2 ubox - 2015-11-22-c086167a0154745c677f8730a336ea9cf7d71031 ubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e ubusd - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e uci - 2015-08-27.1-1 uclibcxx - 0.2.4-1 uhttpd - 2015-11-08-fe01ef3f52adae9da38ef47926cd50974af5d6b7 uhttpd-mod-ubus - 2015-11-08-fe01ef3f52adae9da38ef47926cd50974af5d6b7 usbutils - 007-1 usign - 2015-05-08-cf8dcdb8a4e874c77f3e9a8e9b643e8c17b19131 wireless-tools - 29-5 wpa-cli - 2015-09-27-1 wpa-supplicant-p2p - 2015-09-27-1 zlib - 1.2.8-1 zoneinfo-europe - 2015d-1
/proc/mtd
root@OpenWrt:/# cat /proc/mtd dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "u-boot-env-bak" mtd3: 00010000 00010000 "reserved" mtd4: 00010000 00010000 "art" mtd5: 00200000 00020000 "kernel-0" mtd6: 02000000 00020000 "root-0" mtd7: 00200000 00020000 "kernel-1" mtd8: 02000000 00020000 "root-1" mtd9: 03c00000 00020000 "overlay" mtd10: 02200000 00020000 "firmware1" mtd11: 0141a000 0001f000 "rootfs" mtd12: 007fe000 0001f000 "rootfs_data"
/proc/cmdline
root@OpenWrt:/# cat /proc/cmdline ubi.mtd=8 ubootsvn=5120 board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init bootslot=1 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0),32m(root-0),2m(kernel-1)ro,32m(root-1),60m(overlay),34m@0x2200000(firmware1) production=0000 hwversion=V2.0 app_switch=default mem=64M rootfstype=squashfs,jffs2 noinitrd
/sys/kernel/debug/gpio
root@OpenWrt:/# cat /sys/kernel/debug/gpio GPIOs 0-17, ath79: gpio-3 (cus531:gpio3:reset ) out hi gpio-4 (WPS button ) in lo gpio-12 (cus531:green:power ) out lo gpio-13 (cus531:green:wan ) out hi gpio-14 (cus531:green:lan ) out hi gpio-15 (RESET button ) in lo gpio-16 (scl ) in hi gpio-17 (sda ) in hi
hardware/perenio/peacg01.1643999055.txt.gz · Last modified: 2022/02/04 18:24 by root
