Differences

This shows you the differences between two versions of the page.

--- hardware:d-link:dir-506l [2022/02/17 05:01]
– removed - external edit (Unknown date) 127.0.0.1
+++ hardware:d-link:dir-506l [2022/03/02 23:01]
– [Download] root
@@ Line 1: / Line 1: @@
+====== D-Link DIR-506L ======
+is a portable router with battery.\\
+{{:hardware:d-link:dir-506l_a2.jpg?200|}}
+===== Hardware =====
+  * Ralink RT5350 id:1 rev:3 (360 MHz)
+  * 32 MB RAM
+  * 8 MB Flash
+  * 802.11bgn 1T1R
+  * 1x internal, non-detachable antenna
+  * 1x 10/100 Mbps Ethernet
+  * 1x USB 2.0 (Type-A)
+  * 5 leds
+  * 2 buttons
+  * UART header on PCB (57600 8n1)
+  * JBOOT bootloader
+  * 1700 - 2200 mAh battery (Fujifilm NP-120 / Pentax D-Li7, D-L17, DB-43)
+==== GPIO ====
+=== In ===
+  * 2@gpio0: reset - KEY_RESTART (GPIO_ACTIVE_LOW)
+  * 7@gpio0: wps - KEY_WPS_BUTTON (GPIO_ACTIVE_LOW)
+  * 10@gpio0: low_battery - BTN_0 (GPIO_ACTIVE_HIGH)
+  * 11@gpio0: charging - BTN_1 (GPIO_ACTIVE_HIGH)
+  * 12@gpio0: on_battery - BTN_2 (GPIO_ACTIVE_HIGH)
+=== Out ===
+  * 9@gpio0: led green:usb (GPIO_ACTIVE_LOW)
+  * 18@gpio0: usb port power (GPIO_ACTIVE_HIGH)
+  * 19@gpio0: led green:status (GPIO_ACTIVE_HIGH)
+  * 0@gpio1: led green:internet (GPIO_ACTIVE_HIGH)
+  * 1@gpio1: led red:status (GPIO_ACTIVE_HIGH)
+==== Power usage ====
+With [[hardware:huawei:e3272|Huawei E3272]] + 1 WiFi connection
+  * 240mA IDLE
+  * 600+mA at download speed 5mbps
+\\
+Uptime: ~4 hours with 3 connected clients.
+===== Photos =====
+{{:hardware:d-link:img_2725.jpg?200|}}
+{{:hardware:d-link:img_2728.jpg?200|}}
+===== Modding =====
+==== Power ====
+To allow work without battery add resistor 15-16kOmh\\
+{{:hardware:d-link:img_2726.jpg?200|}}
+==== Micro USB ====
+{{:hardware:d-link:p1010477.jpg?200|}}
+==== Headsink ====
+{{:hardware:d-link:p1010479.jpg?200|}}
+{{:hardware:d-link:img_2735.jpg?200|}}
+===== OpenWRT =====
+==== Features ====
+  * upgrade from stock f/w via WebUI
+  * all LEDs available
+  * all buttons work
+  * battery/charger GPIO events added
+  * USB power on by default
+  * keep JBOOT recovery
+==== Installation ====
+Apply factory image via http web-gui or JBOOT recovery page
+==== Download ====
+[[http://www.netlab.linkpc.net/download/software/openwrt/DIR-506L/|DIR-506L]]
+[[https://github.com/rozhuk-im/openwrt/commits/all_local|github.com]]
+==== Known issues ====
+=== Upgrade hang ===
+Upgrade may hang, at least then WebUI used.\\
+Workaround: stop unbound and dnsmasq before upload f/w to release memory.
+=== Net hang on boot ===
+Happen then internal switch exist and disabled.\\
+<code>NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out</code>
+[[https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/377]]\\
+[[https://github.com/openwrt/openwrt/issues/8660]]\\
+Workaround: unplug net cable untill device started\\
+Workaround: remove switch from existing configuration or build f/w without defined switch in 02_network and reset config on/after update
+==== How to revert to OEM firmware ====
+  * push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
+  * upload original factory image via JBOOT http (IP: 192.168.123.254)
+\\
+If http doesn't work, it can be done with curl command:
+<code>curl -F FN=@XXXXX.bin http://192.168.123.254/upg</code>
+where XXXXX.bin is name of firmware file.
+{{tag>hardware reverse linux openwrt d-link router}}

Net Lab

User Tools

Site Tools

Differences

Page Tools